config_echomail_nodes
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
config_echomail_nodes [2022/09/26 02:01] – adding netmail logic changes avon | config_echomail_nodes [2023/01/03 01:49] (current) – [Page 4 of 6 - BinkP] upload/download limits added avon | ||
---|---|---|---|
Line 169: | Line 169: | ||
* If a node is still not found then Mystic will look for a zone match, and finally if no zone match is found then the Netmail will fail to route. | * If a node is still not found then Mystic will look for a zone match, and finally if no zone match is found then the Netmail will fail to route. | ||
- | This system allows for Netmail to work automatically without any knowlege | + | To further expand on the automatic Netmail routing logic, Mystic will now perform a FidoNet fuzzy zone match when auto routing Netmail. |
+ | |||
+ | To reiterate: For almost everyone, there is never a need touch the Route field in your Echomail node editor. | ||
+ | |||
+ | This system allows for Netmail to work automatically without any knowledge | ||
=== Uplink === | === Uplink === | ||
Line 333: | Line 337: | ||
==== Page 4 of 6 - BinkP==== | ==== Page 4 of 6 - BinkP==== | ||
- | |||
BINKP Hostname │ net1.fsxnet.nz | BINKP Hostname │ net1.fsxnet.nz | ||
IP Type │ IPV4 2:Security | IP Type │ IPV4 2:Security | ||
- | | + | Server Type │ Normal |
- | Time Out │ 30 | + | Password |
- | Block Size │ 16384 5:FTP | + | Time Out │ 30 |
- | | + | Block Size │ 16384 6:Dir Toss |
+ | | ||
Hide AKAs │ Yes | Hide AKAs │ Yes | ||
- | | + | |
- | │ | + | Upload Limit │ 0 |
- | │ | + | Download Limit │ 0 |
│ | │ | ||
│ | │ | ||
│ | │ | ||
│ Page 4 of 6 | │ Page 4 of 6 | ||
- | |||
A Binkp section has the following options you should look at and in most cases set up: | A Binkp section has the following options you should look at and in most cases set up: | ||
Line 359: | Line 362: | ||
Do you wish to use IPV4 or IPV6 when using MIS POLL to connect to this system? Or do you wish to set a preferred connection type and then a fallback type? e.g. IPV6 + IPV4 or IPV4 + IPV6 | Do you wish to use IPV4 or IPV6 when using MIS POLL to connect to this system? Or do you wish to set a preferred connection type and then a fallback type? e.g. IPV6 + IPV4 or IPV4 + IPV6 | ||
+ | |||
+ | === Server Type === | ||
+ | |||
+ | There are four possible options for this setting: | ||
+ | |||
+ | * Normal | ||
+ | * Direct SSL : Connect with a direct SSL connection | ||
+ | * StartTLS (If Available) : Use TLS when available | ||
+ | * StartTLS (Required) | ||
+ | |||
+ | The StartTLS Required option will refuse to authenticate with any server that does not offer the opportunistic TLS upgrading. These features require that CryptLib is present and detected by Mystic. | ||
=== Password === | === Password === | ||
Line 381: | Line 395: | ||
Hide alternative network addresses during a BinkP handshake. When your system polls this EchoMail Node will it only show the network address you have set up for the same Zone this EchoMail Node has in common with or it will show all your defined EchoMail addresses? | Hide alternative network addresses during a BinkP handshake. When your system polls this EchoMail Node will it only show the network address you have set up for the same Zone this EchoMail Node has in common with or it will show all your defined EchoMail addresses? | ||
+ | |||
+ | === Escape Mode === | ||
+ | |||
+ | Mystic' | ||
+ | |||
+ | This setting determines how Mystic will escape special characters in filenames and defaults to the Auto setting. | ||
+ | |||
+ | When set to **Auto**, Mystic will automatically try to determine the escape mode by using the VERSION frame sent by the mailer. | ||
+ | |||
+ | When set to **Legacy**, Mystic will use the \## format of file escaping which is used in some legacy mailers such as Argus, Internet Rex, and older versions of Mystic. | ||
+ | |||
+ | When set to **Modern**, Mystic will use the \x## format which is preferred or even required by some newer mailers such as BinkD, Radius, and BinkIT. | ||
+ | |||
+ | It is highly recommended to always keep these set to AUTO unless there is a very specific reason not to. The escape mode will be logged after authentication if the loglevel is set to Verbose or higher. | ||
+ | |||
+ | === Upload Limit === | ||
+ | |||
+ | Set the upload speed limit: (Used when you send files to this node) | ||
+ | |||
+ | BINKP has the ability to limit the bandwidth used when sending or receiving files. | ||
+ | |||
+ | === Download Limit === | ||
+ | |||
+ | Set the download speed limit: (Used when you receive files from this node). This setting overrides MIS POLL/BINKP settings if enabled. | ||
==== Page 5 of 6 - FTP ==== | ==== Page 5 of 6 - FTP ==== |
config_echomail_nodes.1664175676.txt.gz · Last modified: 2022/09/26 02:01 by avon